[1]陈建芳,陈海飞,汪城.叶片进口安放角对单叶片离心泵内流场的影响[J].常州大学学报(自然科学版),2022,34(06):27-33.[doi:10.3969/j.issn.2095-0411.2022.06.004]
　CHEN Jianfang,CHEN Haifei,WANG Cheng.Influence of Blade Inlet Angle on the Inner Flow Field of Single-Blade Centrifugal Pump[J].Journal of Changzhou University(Natural Science Edition),2022,34(06):27-33.[doi:10.3969/j.issn.2095-0411.2022.06.004]
点击复制

叶片进口安放角对单叶片离心泵内流场的影响()
分享到：

常州大学学报(自然科学版)[ISSN:2095-0411/CN:32-1822/N]

卷:
第34卷
期数:
2022年06期
页码:
27-33
栏目:
机械制造及其自动化
出版日期:
2022-11-28

文章信息/Info

Title:
Influence of Blade Inlet Angle on the Inner Flow Field of Single-Blade Centrifugal Pump
文章编号:
2095-0411(2022)06-0027-07
作者:
陈建芳1; 陈海飞2; 汪城2
(1.常州大学城市建设学院,江苏常州213164;2.常州大学石油与天然气工程学院,江苏常州213164)
Author(s):
CHEN Jianfang1;  CHEN Haifei2;  WANG Cheng2
(1.School of Urban Construction, Changzhou University, Changzhou 213164, China; 2.School of Petroleum and Natural Gas Engineering, Changzhou University, Changzhou 213164, China)
关键词:
单叶片离心泵;  进口安放角;  压力分布;  速度分布;  叶片载荷
Keywords:
single-blade centrifugal pump;  blade inlet angle;  pressure distribution;  velocity distribution;  blade loading
分类号:
TH 311
DOI:
10.3969/j.issn.2095-0411.2022.06.004
文献标志码:
A
摘要:
文章利用ANSYS Bladegen软件,设计了4种不同叶片进口安放角的叶轮。对采用不同叶轮的单叶片离心泵进行了全流场定常数值计算,并通过试验验证了所采用数值计算方法的可靠性。结果表明:额定转速下,流量越大,叶轮中间截面上压力分布越均匀,但叶轮入口处和蜗壳内的低速区范围越大,同时叶轮出口绝对速度的波动程度受叶片进口安放角的影响越小。同一工况下,适当增大叶片进口安放角可增加叶轮中间截面上高压区的范围,提高叶轮能量转换能力,但会降低叶片吸力面入口处的压力。所有流量工况下,叶片进口安放角太小或太大均不利于降低叶轮流出液流与蜗壳中液流发生碰撞产生的碰撞损失,同时不利于降低叶片所受载荷的波动程度。
Abstract:
In this paper, four impellers with different blade inlet angles were designed by using ANSYS Bladegen software. The steady numerical calculation of whole flow field of single-blade centrifugal pump with different impellers was carried out, and the numerical calculation scheme adopted was verified. The results show that the pressure distribution on the middle section of the impeller is more uniform, but the range of low-velocity zone at the impeller inlet and in volute is larger, and the fluctuation of absolute velocity at the impeller outlet is less affected by the blade inlet angle with the increase of flow rate at the rated rotating speed.Under the same working condition, properly increasing the blade inlet angle can increase the range of high pressure area on the middle section of the impeller and improve the energy conversion capacity of the impeller, while reducing the pressure at the inlet of the blade suction surface.Under all flow conditions, the blade inlet angle is too small or too large, which is not conducive to reducing the collision loss caused by the collision between the liquid flow from the impeller and the liquid flow in volute, reducing the fluctuation of the blade load.

参考文献/References:

[1] AOKI M. Instantaneous interblade pressure distributions and fluctuating radial thrust in a single-blade centrifugal pump[J]. Bulletin of JSME, 1984, 27(233): 2413-2420.
[2] DALY J, De Souza B, NIVEN A,et al. Numerical simulation of transient flow and Head distribution through a single blade centrifugal pump impeller[C]//Proceedings of the 4th WSEAS International Conference on Fluid Mechanics and Aerodynamics. Greece: [s.n.], 2006: 343-348.
[3] FRAWLRY P, NIVEN A, DE SOUZA B, et al. Numerical simulation and analysis of the transient flow and head distribution through a single blade centrifugal pump impeller[J]. WSEAS Transactions on Fluid Mechanics, 2006, 1(6): 678-685.
[4] NISHI Y, FUKUTOMI J, FUJIWARA R. Effect of blade outlet angle on radial thrust of single-blade centrifugal pump[J]. IOP Conference Series: Earth and Environmental Science, 2012, 15(7): 072039.
[5] NISHI Y, FUKUTOMI J. Effect of blade outlet angle on unsteady hydrodynamic force of closed-type centrifugal pump with single blade[J]. International Journal of Rotating Machinery, 2014, 2014: 838627.
[6] NISHI Y, FUKUTOMI J. Component analysis of unsteady hydrodynamic force of closed-type centrifugal pump with single blades of different blade outlet angles[J]. International Journal of Rotating Machinery, 2015, 20(3): 1-17.
[7] AUVINEN M. Computational analysis of a single-blade sewage pump with FINFLO[C]//Helsinki University of Technology Laboratory of Applied Thermodynamics. Puerto Rico: ICLR, 2006.
[8] AUVINEN M, JUUSELA J A, ILVES L, et al. Dissecting a complex system:a computational study of flow behavior in a single-blade pump[C]//Proceedings of the 5th International Conference on Heat Transfer, Fluids Mechanics and Thermodynamics. Netherlands: [s.n.], 2007.
[9] AUVINEN M, JUUSELA J A, PEDERSEN N,et al.Time-accurate turbomachinery simula-tions with open source CFD: flow analysis of a single-channel pump with open FOAM[C]//Proceedings of the 5th European Conference on Computational Fluid Dynamics. Lisbon: [s.n.], 2010.
[10] 裴吉, 袁寿其, 袁建平, 等. 单叶片离心泵压力脉动强度多工况对比研究[J]. 华中科技大学学报(自然科学版), 2013, 41(12): 29-33, 53.
[11] 谭林伟, 施卫东, 张德胜, 等. 叶片出口安放角对单叶片泵性能的影响[J]. 排灌机械工程学报, 2017, 35(10): 835-841, 855.
[12] 谭林伟, 施卫东, 张德胜, 等. 离心泵水力诱导激振试验研究[J]. 农业机械学报, 2018, 49(5): 179-185.
[13] 汪源. 单叶片潜水排污泵径向力特性的研究[D]. 合肥: 合肥工业大学, 2018.
[14] 陈建芳, 施卫东, 张德胜, 等. 叶片进口边位置对单叶片离心泵蜗壳内压力脉动的影响[J]. 振动与冲击, 2021, 40(23): 239-246.
[15] 陈建芳, 施卫东, 张德胜. 叶片进口边位置对单叶片离心泵性能的影响[J]. 排灌机械工程学报, 2021, 39(11): 1093-1099.
[16] 关醒凡. 现代泵理论与设计[M]. 北京: 中国宇航出版社, 2011.
[17] CHEN J F, SHI W D, ZHANG D S. Influence of blade inlet angle on the performance of a single blade centrifugal pump[J]. Engineering Applications of Computational Fluid Mechanics, 2021, 15(1): 462-475.
[18] 付双成, 张亚磊, 姜毓圣, 等. 卧螺离心机不同螺旋结构流场的数值模拟研究[J]. 常州大学学报(自然科学版), 2020, 32(1): 56-61.
(责任编辑:李艳)

备注/Memo

备注/Memo:
收稿日期: 2022-06-06。
基金项目: 江苏省研究生科研与实践创新计划资助项目(KYCX21_2813); 常州大学校企合作资助项目(KYH21020542)。
作者简介: 陈建芳(1977—), 女, 河北馆陶人, 硕士, 讲师。E-mail: cjf2004@cczu.edu.cn
更新日期/Last Update: 1900-01-01